POTENSI PASIR LOKAL TANJUNG BINTANG PADA ALUMINIUM SAND CASTING TERHADAP POROSITAS PRODUK HASIL COR ALUMINIUM

Yusup Hendronursito, Yogi Prayanda

Abstract


Green sand is one of the most important components in the process of metal casting. The sand in Indonesia region is varied level of subtlety, size of sand, and shape of sand. Green sand used in the process of metal casting is possible can affect the quality of casting product. This aims to determine the potential of Tanjung Bintang sand as green sand and the quality of the product in terms of porosity defects. The research was conducted by varying sand river from Tanjung Bintang and sand from Maringgai. Composition made varying  is 100%,75%, 50%, and 25% Tanjung Bintang sand compared Maringgai sand with bentonit and water is 10% and 5% constantly .The Examine of the green sand by SNI 15-0312-1989 among other water content, clay content, Grain Finnest Number (GFN), Shape of grain. The result said aluminium casting product with  50% Tanjung Bintang sand has the lowest value of porosity, 5.08% and the higher value with 75% composition of Tanjung Bintang sand, 6.98%.


Full Text:

PDF

References


Astrid P. N., Bona M., Irma S., Nadia F. R., Prila S. L. R., Ira W., 2007, , Pengujian Pasir Cetak, Laporan Praktikum Proses Manufaktur Modul V, Teknik Mesin, Institut Teknologi Bandung.

Nurwidyanto M.I., Meida Y., Sugeng W., 2006, Pengaruh Ukuran Butir Terhadap Porositas Dan Permeabilitas Pada Batupasir, Berkala Fisika, Vol. 9, No.4, 191-195.

Sidiq B., Budi H., Yuyun E., 2014, Perbandingan Kualitas Hasil Pengecoran Pasir Cetak Basah Dengan Campuran Bentonit 3% Dan 5% Pada Besi Cor Kelabu, Jurnal Nosel, Vol. 2, No. 3

Dody A., Wahyu P. R., Saiful A., 2006, Hubungan Variasi Jenis Pasir Cetak Terhadap Sifat Mekanik Besi Cor Kelabu, Jurnal Mekanika, Vol. 4, No. 2.

Uswatun S., 2012, Analisis Variasi Pasir Cetak Lokal Jawa Timur Terhadap Kekuatan Cetakan Pasir, Fluiditas, Dan Kualitas Hasil Coran Logam Al-Si Dengan Metode Gravitasi Casting, Skripsi, Fakultas Teknik Um.

Standar Nasional Indonesia (SNI) 15-0312-12-1989, 1989. Pasir cetak, Cara uji. Badan Standarisasi Nasional. ICS 91.100.15

Rizal M. P., Soeharto., 2012, Studi Eksperimen Pengaruh Jenis Saluran pada Aluminium Sand Casting terhadap Porositas Produk Toroidal Piston, Jurnal Teknik ITS Vol. 1, No. 1, 126 – 130

Supriadi, H., Sewandono, D., 2013, Pengaruh Variasi Abu Sekam Dan Bentonit Pada Cetakan Pasir Terhadap Kekerasan Dan Struktur Mikro 2) 1) Hasil Coran Alumunium Aa 1100. Jurnal Ilmiah Teknik Mesin, Vol.1 No.3

Budinski G. K., 1996, Engineering Material Properties and Selection, Prentice Hall, Inc, Englewood Cliffs, New Jersey




DOI: https://doi.org/10.52447/jktm.v1i2.336

Refbacks

  • There are currently no refbacks.